Sree Ramraj Dyes & Chemicals

Reflective ink is a Water-based inks formulated for direct printing on textiles. The base is combined with aluminum-coated glass beads to produce a highly reflective ink. This base is non-pigmented/noncolored. It is a ready colored ink. We have Reflective ink for Direct Printing and Reflective Sheets which is for Transfer printing.  These Reflective inks are made up of a carrier base and small reflective glass beads.

Process:

• Always stir the ink thoroughly before printing. Stirring the ink distributes the beads more evenly throughout the carrier before the design is printed. One flood coat and one squeegee print will generally yield the most reflectivity. Printing in this manner will allow the base coat to settle into the fabric, leaving the reflective particles on top where they can catch the light. Multiple print strokes will lay down too much of the base and the reflective beads won’t sit on top of the fabric evenly or catch the light properly.

Mesh:

• Mesh count from 32 T (80 Nylon) is highly recommended. Using a mesh count that’s too fine will strain the reflective particles from the carrier base. Less reflective beads mean less reflectivity. It’ll also result in a mesh that’s clogged with reflective beads.

Squeegees:

• 75 durometer or triple durometer 70/90/70 Squeegee blade Sharp, straight edge

Curing:

• Curing is to be done at 340-350 F (171-177 C) for the entire film

It is Water-based High Glossy ink, that can be been Garment Dyed even after Printing with Pu Glossy ink. It is a Top Coat, that can be printed over Khadi, Water paster and Non-Pvc water-based ink. It has more Soft feel effect. 

Mesh:

• 80- 120 Nylon mesh

Squeegees:

• 65-75 Shore, for the first impression 75-85 shore for the second impression 2nd impression with V-shaped Squeegees is highly recommended

Curing:

• Curing can be done at 160" Degree for 1.5 mins

This is water based Antex SP236 Foil Gel for Screen printing, the foil can be pallet released and heat pressed. Hand feel is very soft. The foil paper can be heat pressed and released even after 1 week of gel printed. High Washing durabilty can be obtained.

It is a water based printing paste used to obtain elastic and soft touching silver pearl effect in textile printing. It can be printed on cotton and white and light colored cotton – polyester blend fabrics. It has a good shinning effect and washing fastness, the simmer doesn't lose the shinning effect even after months.In order to have more covering, colour productivity and elasticity in the print of Silver simmer-WB double print is advised with flash cure. 

Mesh:

• Silk screens that are made of 32 cm/80 inch mesh 80 micron silk. 43 cm/110 inch mesh 70 micron silk should be used.

Squeegees:

• 57 - 62 Shore U type squeegee should be used.

Curing:

• Should be cured at 160 °C/320ËšF for 1,5 minutes.

It is Waterbase Manual Crack Printing Ink these print needed to pulled to attain crack effect. 

Ecosol E1 is Non PVC, Phthalate and Formaldehyde high solid content, waterbase thermoplastic acrylic.

Ecosol E1 System is an excellent product for use for printing depth dark shade on light color fabrics where excellent finish, elastomeric and soft hand feel are required. Motive printed with Ecosol will have excellent elastomeric properties, good washing fastness properties, good crocking properties and high color brilliancy.

Ecosol E1 System consists of White, High Opaque Base, and Clear. Printers are recommended to match colors using Pigments concentrated colors for optimum colors and performance.

Mesh:

• 32T~43T (80-100) mono-filament for Metallic, Glitter, and Shimmer. 49~52S(120-130) mono-multi filament for under base white. 77~120S (200-300) mono-multi filament for detail print or for out line and tone on fabric

Sqeegers:

• 55/65 sore hardness: For excellent opacity on printing under base white, are recommended. 65 sore hardness : For wet on wet for multi color printing. 75/85 sore hardness :For detail and fine toning effect.

Curring Condition:

• For maximum fastness, prints are to be cure at 150ºC/302°F. Airflow recommended is 1500 cfm/ 46cmm for 2 minutes.

Type of Fabrics:

• Cotton, Blends Cotton Polyester and some stretchable Cotton /Nylon

Color Matching:

• Always use Ecosol E1 Opaque Base in color matching. Commonly 10 to 15% of Pigments are used to achieve desire color. High glossy color can be achieved by using Ecosol E1 Clear. Use small dosage of Ecosol E1 White when opacity and pastel color effect are required.

 

This system consists of two different pastes which are Auto Crack White and Auto Crack Clear.

Auto Crack White is a high opaque white and Auto Crack Clear is Clear base , which both of them form a super hard dry film with low coalescing properties when dry. These are ready for use water base cracking ink that can be screen printed immediate out of its can.

Auto Crack White is an excellent product for use on dark fabrics where maximum opacity with cracking finish is required, where else Auto Crack Clear is a highly translucent base that can be used in conjunction with a wide range of waterbased pigment concentrated to achieve desire colors of the crack print.

Process:

• Underbase should be touch dry prior laying down the cracking paste. First Print 1 Time Auto Crack basecoat that should be touch dry prior laying down the cracking paste. then print Auto Crack White / Clear mixed Colour 2 Times with 3 Strock. Natural Dry the fabric, you can see the Crack immediately, don't remove the fabric from table/ pallet before complete cracking, as Cracking will not happen once removed from pallet.

Mesh:

• 43S/110S - 49S/120S mono-filament at 20 Newton for high opacity. 39T/100T-51T/130T mono-filament at 20 Newton for cracking paste with emulsion thickness of 200µm. 100 Nylon Mesh.

Squeegees:

• For maximum opacity 50/60 durometer hardness squeegees are recommended for underbase. To achieve an excellent cracking effect use 45/55 durometer hardness squeegees. Soft tables are most and multiple squeegee strokes are recommended to improve on cracking ink deposit.

Drying:

• All underbase should be touch dry prior laying down the cracking paste. To achieve even cracking, all intermediate cracking color is to be cool air dry at temperature below 50°C/122°F. Final drying and cracking are suggested at 150°C/302°F for 3 minutes with Airflow recommended are 2500 cfm/70.79cmm for proper polymerization.

It is Silicone High Glossy Screen Printing Inks. Need to be printed with 2% catalyst. 

Silicone High Glossy Screen Printing Inks.

The Print Colour Changes By temperature and water.